Meego 1.2 on CrossvilleST

Discussion:

Klaus Huber

2011-09-13 09:52:41 UTC

Hello everyone,

Which image can I use to install Meego 1.2 IVI on CrossvilleST?
The board I am using is a Brookville Rev A2.

I tried meego-conx-1.2.0.5.27.tar.gz from
http://wiki.meego.com/IVI_Images_for_ConneXt_IOH but only get a kernel
error right after selecting "Installation only" or "Boot Meego".
The same image works on a Millville Rev C0 board.

I really would like to post the kernel error but can only see the end
of the dump. The beginning scrolls too fast and scrolling upwards does
not work.
Any ideas?

Best regards,
Klaus

Hahn, Matthias

2011-09-13 14:37:53 UTC

Permalink

Hi Klaus,

I have this very image running on CV-ST Brookville Rev.A2. Haven't come
across a kernel error at the stage you mention (at least once I ran the
graphical installer up to a certain point from which on I had to complete
the installation manually)
Note however: there have been some problems with installers. I often run the
installation manually. (dd the content of the ext3fs included in the
liveimage over manually, dd'ing syslinux mbr.bin, running extlinux -I,
adopting /etc/fstab, creating extlinux.conf)

Dr. Matthias Hahn
Intel GmbH
Tel. +49 89 99143-865
Cell +49 173 6514578

-----Original Message-----
From: meego-ivi-bounces-***@public.gmane.org
[mailto:meego-ivi-bounces-***@public.gmane.org] On Behalf Of Klaus Huber
Sent: Tuesday, September 13, 2011 11:53 AM
To: meego-ivi-***@public.gmane.org
Subject: [MeeGo-ivi] Meego 1.2 on CrossvilleST

Hello everyone,

Which image can I use to install Meego 1.2 IVI on CrossvilleST?
The board I am using is a Brookville Rev A2.

I tried meego-conx-1.2.0.5.27.tar.gz from
http://wiki.meego.com/IVI_Images_for_ConneXt_IOH but only get a kernel
error right after selecting "Installation only" or "Boot Meego".
The same image works on a Millville Rev C0 board.

I really would like to post the kernel error but can only see the end
of the dump. The beginning scrolls too fast and scrolling upwards does
not work.
Any ideas?

Best regards,
Klaus

Foster, Susan B

2011-09-19 19:44:23 UTC

Permalink

Hi Klaus,

What version of Abbeville are you using? Is it CUT1 or CUT2?

Susan Foster

Email: susan.b.foster-***@public.gmane.org
Voice: +1 (480) 552-0927
Inet: 85520927

-----Original Message-----
From: meego-ivi-bounces-***@public.gmane.org [mailto:meego-ivi-bounces-***@public.gmane.org] On Behalf Of Klaus Huber
Sent: Tuesday, September 13, 2011 2:53 AM
To: meego-ivi-***@public.gmane.org
Subject: [MeeGo-ivi] Meego 1.2 on CrossvilleST

Hello everyone,

Which image can I use to install Meego 1.2 IVI on CrossvilleST?
The board I am using is a Brookville Rev A2.

I tried meego-conx-1.2.0.5.27.tar.gz from http://wiki.meego.com/IVI_Images_for_ConneXt_IOH but only get a kernel error right after selecting "Installation only" or "Boot Meego".
The same image works on a Millville Rev C0 board.

I really would like to post the kernel error but can only see the end of the dump. The beginning scrolls too fast and scrolling upwards does not work.
Any ideas?

Best regards,
Klaus